ART OF COPPERSMITHING. A PRA C TIC A L TR EATlSE O N WO R KIN G S H EET. C O PPER IN TO A LL FO R M S. j O H N. F U L L E R,. S E. PU BLISHED . PAGE Historical Sketch of Copper u Braziers’ Art, or Light Coppersmithing 16 First Year’s .. 10; then close the whole up close ART OF COPPERSMITHING. Fio. Art Of Coppersmithing has 13 ratings and 3 reviews. Casey said: Read this while working at San Francisco’s Building Resources. The diagrams were cool and.
|Published (Last):||22 April 2013|
|PDF File Size:||18.13 Mb|
|ePub File Size:||8.60 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sauce pan handles, Fig.
One man or boy gave the blow while the other manipulated the work under it. Mark Kingston rated it it was amazing Dec 17, Preserving pans are made in the same way -as warming pans, described in the previous chapter. Cut it out, bend round and braze the joint; trim the seam, knock it down and anneal; take in a course on the head secured in a square shank, as shown in Fig.
Art Of Coppersmithing: A Practical Treatise On Working Sheet Copper Into All Forms by John Fuller
Frying-pans are made flaring in the ratio of about 2 to 1 — that is, if the side be 2 inches deep, then the flare on the side will be 1 inchj or coppersmithlng other words, if coppersmithinv a pan be 12 inches at the top the bottom will be 10 inches.
The old Romans knew copper as aes cyprum, and later as cyprutn, names apparently derived from that of the island of Cyprus, where Pliny says the art of working it was first discovered. The work of making stock pots is the same as that of large deep stew pans, excepting that the cover is made to fit on over the outside, and deep enough to be used as a cutlet pan, the pot and cover being mounted with cast coppersmitthing handles as shown.
Read this while working at San Francisco’s Building Resources. Stewpans were made light or heavy to suit the wants of the pur- cop;ersmithing, or to meet competition in price; generally they were made heavy. Now take a racer and mark around the middle of the body, and wrinkle it at one end as far as the middle Fig.
Now true it up to size and shape, then planish and put in the wire. After the writer was made to understand why he had been placed in that old shop, he was usually the first to arrive and the last out, and became much attached to the trade; particularly after having seen the first half-dozen bright copper tea-kettles finished and cleaned ready for the show-room, he looked forward to the time when he could imi- tate them.
Let us cut one out, required to measure 16 inches, and pro- ceed to work copprsmithing up.
Full text of “Art of Coppersmithing: A Practical Treatise on Working Sheet Copper Into All “
The body of a braising pan, Fig. We will make one to be 3 inches deep when finished, having the corners round ot brazed, as shown in Fig. I then resolved to exert every effort to acquire the neces sary ability, so that when a favorable opportunity should offer I could give my experience for the benefit of boys placed in the same unfortunate position as myself.
Then a line traced through the intersections thus established, as indicated by V W, will be the pattern joining the cone, as shown in the elevation from C to B.
Many an otherwise good piece of work has been spoiled for the want of proper symmetry in the mountings or carelessness in their finish.
The strength of the material may be governed by the price at which it is desired to sell the finished articles, but the usual weight was 8, 9 and xo pound plate for the sides of each size respectively and io, ii and ccoppersmithing pound for the bottoms. If the scoop is to have the sides of the bottom or body as shown by the semicircle a k b y then the bridge is again shown by a efb, taking the solid line area on each side as the shape.
Next put on the ears, the rivet holes of which should be countersunk enough so that the rivet heads may be drawn in and be flush and smooth with the surface inside.
After the ring is made and wired, take a creasing hammer and then sink coppermithing bead in a coppers,ithing stake, as shown in Fig. This primitive contrivance is a round bar having the ends turned square about 5 inches, coplersmithing and then bolted to the bench, leaving a space between it and the edge of the bench wide enough to get the sheet iron or copper between, the workman forming the pipe arg bending the sheet over the bar with the leverage of the metal.
The strig or lever coppersithing finally soldered on and the article cleaned ready for the store-room. Books by John Fuller. We may now proceed with the planishing. To ask other readers questions about Art Of Coppersmithingplease sign up. After the seam has been made and the body annealed, take in a course on a side stake, as previously explained in Fig. Inhowever, the crisis came, and of the then hundreds of nominally existing companies only six were found actually engaged in mining.
From these points draw radial lines to Y, as indicated. This is probably one of the best lessons in the trade for a boy or man either who desires to be fa- miliar with the art of measuring and converting surfaces into forms suited for the work in hand.
In preparing this Fourth Edition, I have carefully examined the work and amended, transposed and placed the figures spoken of in the text close to each other copperzmithing that both text and illustration are under the eye of the reader as much as possible.
No trivia or quizzes yet. The Piece Put Thbouoh Iheidb. Now describe with the compasses the size of the bottom on the pattern Fig.
Art of Coppersmithing
These spherical floats have a long strig or lever made of copper soldered to them, having a square hole in it to fit on the square of the plug of a cock, as shown in Fig. They however, all demand proficiency and along, care- ful training with much patience to acquire the skill necessary for the execution of the various steps through which they pass to completion. The peaked muller, Fig.