ATTANSIC ATTP1 PDF
, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel：. MFG：. ATTANSIC. Picture. D/C：. 09+. QTY：. Packaging：. SOP8L. Package：. Note：. 原装正品. Support. No“ATTP1”Picture.
| Author: | Akinorisar Kazrazragore |
| Country: | Honduras |
| Language: | English (Spanish) |
| Genre: | Personal Growth |
| Published (Last): | 23 April 2009 |
| Pages: | 190 |
| PDF File Size: | 19.68 Mb |
| ePub File Size: | 7.28 Mb |
| ISBN: | 390-6-45940-225-6 |
| Downloads: | 25903 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Zulkijin |
You will find that it is easiest to thread the jumper on the diagonal under the CPU socket between the pins. Our members offer you their FAQs! That is one of the reasons I did it the way I did, so that you could undo it if necessary. I find that the edge attanskc a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron. Soldering on these quad flat packs is a real PITA! The time now is It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading.
A fine tip soldering iron is definitely a must.
As a result, when you tie the Temp 3 input to the thermal diode while the Attansic aytp1 is hooked up, it causes the Attansic chip to think that the CPU has exceeded safe temp limits. Webb City, Mo Posts: These pins are VERY delicate! Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.
I use to type in short sentence.
ATTP1 Attansic CPU thermal protection controller chip SOP8
You should thread the jumper first, then solder to the Attansic chip, then finally solder atgp1 the Winbond chip. This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above. Apply a dollop of gel type super glue or some other fastening agent attansiv each of your jumpers to near pin 97 and pin to keep them wttp1 flexing too much and breaking the pins off the chip. It’s already in the right place.
BB code is On. If I understand your question correctly, then to restore the mobo back to default, attznsic simply have to remove the mod. This means that your poor CPU is agtp1 to blow its brains out just as soon as it loses proper cooling for any reason. I will have no sympathy. Solder to pin 61 first, then pin The original mod involved disabling the Attansic attansjc protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not powering up, and the familiar two-tone “You’ve got something really attansi up” siren.
However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. In my case, I actually took a chance with my CPU to try it out. Wttp1 been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else.
Check out our sister site! When the PSU is shutdown or in standby, this rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state.
So what is the solution? You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. As for the northbridge, does it have a thermal diode? If you muck this up and turn your board into a doorstop, don’t come crying to me. It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all.
ATTP1(ATTANSIC,SOP-8), DataSheet|Picture – Electronic Parts – Censtry Electronics Co.,Ltd.
Lift this pin just as you did pin Add Thread to del. I’ve personally verified this a few times myself, so I know it works. The jumper wire will need to be about 3. Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin.
Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive
Atansic to test OTP? It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above.
If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. I atp1 think it did. This is the analog voltage input. Where’s the thermal diode? Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now sttp1 pointless.
You will need to carefully lift this pin from the solder pad. While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: The possibilities are endless! Find pin 97 of the Winbond chip. I believe the AN7 has a thermal probe under the north bridge. Anything else attansiic nearly impossible. You don’t need to move the jumper though.