For a substitute, please see CP2E. Crestron 2-Series Control Systems are the brain of a complete integrated AV or automation solution. Every audio, video, and . Find great deals for Crestron CP2E Compact Control System W/ Ethernet. Shop with confidence on eBay!. Find great deals for Crestron CP2E Control Processor with Ethernet. Shop with confidence on eBay!.
|Published (Last):||23 April 2017|
|PDF File Size:||4.4 Mb|
|ePub File Size:||15.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Secure the ear to the unit with three screws from step 1, as shown in the following diagram. Crestron has developed an assortment of Windows? Updates may be licensed to You by Crestron with additional or different terms. Only the required pins for each communication type should be connected.
For assistance in your local time zone, refer to the Crestron website http: Either add, modify, or delete entries in the IP table. Serial cable not wired correctly. Verify that hardware configuration matches software configuration. If this software requires payment for a license, you may make one co2e copy of the Software, provided Your backup copy is not installed or used on any CPU. Insulate the strip by folding a piece of?
Failure to do so could cause equipment damage or void the Crestron warranty. Display the network device tree Tools Network Device Tree to show all network devices connected to the control system. Check the Crestron website crestroj for manual update availability and its relevance. Hardware or software failure, hardware incompatibility with software definitions or programming error. Refer to table at right.
For larger networks i. The Cresnet Poll Accelerator effectively increases the network speed, fan-out and device addresses by a factor of 8 for each Poll Accelerator added to the system. If Cresnet units are to be daisychained on the run, the Cresnet power usage of each network unit to be daisychained must be added together to determine the Cresnet power usage of the entire chain. The following are the minimum recommended software versions for the PC: Verify network connection to the device.
Crestron retains ownership cestron the Software and all copies of the Software and reserves all rights not expressly granted in writing.
Required for initial setup of Ethernet parameters. The Software is designed as a software development and customization tool. All Crestron certified Cresnet wiring must consist of two twisted pairs. For more details, refer to the Crestron Toolbox help file.
Dispose of used batteries according to the manufacturer’s instructions. Apply the feet near the corner edges on the underside of the unit.
This may result in a conflict with some equipment and therefore all nine pins should not be used. The Software is licensed and not sold. The CP2 and CP2E are compact control systems designed for small to medium sized residential and commercial control applications.
The failure of either party to enforce any right or take any action in the event of a breach hereunder shall constitute a waiver unless expressly acknowledged and set forth in writing by the party alleged to have provided such waiver. If less than four, the strip can be trimmed to size with a pair of scissors or wire snips.
Avoid tinning too far crestroj the wires or the end becomes brittle. Loosen the terminal block screws and insert the first leg of the bussing strip into the first common position of the terminal block. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire.
To decipher content, examine the message through the Crestron Toolbox?. Any implied warranties that may be imposed by law cresfron limited to the terms of this limited warranty.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
When setting the IP ID, consider the following: To install the ears: However, there is no guarantee that interference will not occur in a particular installation. Shipments arriving freight collect or without an RMA number shall be subject to refusal.
Strip and Tin Wire When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors.
Passthrough Mode enables Viewport access to any serial controlled device on the network. Repeat procedure steps 1 through 3 to attach the remaining ear to the opposite side. You may not transfer the license granted pursuant to this Agreement or assign this Agreement without the express written consent of Crestron.
However, before attempting to upload or upgrade, it is necessary to establish communication. The foregoing remedy shall be your exclusive remedy for any claim or loss arising from the Software.
Crestron CP2E besturingssyteem
This link will provide a list of product manuals arranged in alphabetical order by model number. The Software is protected by copyright laws and international treaty provisions. First-time users will need to establish a user account to fully benefit from all available features. Danger of explosion if battery is incorrectly replaced. Het Crestron 2-series besturingssysteem is het zenuwstelsel van een compleet geintregreerde AV oplossing. CP2E only Every Ethernet-enabled 2-Series control system works directly with Crestron’s exclusive RoomView Help Desk software for the industry’s most comprehensive facility-wide asset management solution.