CRITICAL NOTE: We have found that IPv6 pings sent to the Juniper SSG5 will cause the device to REBOOT. Turning off From here, select the default of “Use the Initial Configuration Wizard instead.” Download Business Routers Guide. Secure Services Gateway 5 users manual details for FCC ID OXVSSG5 made by Juniper Networks Inc.. Document Includes User Manual Every effort has been made to ensure that the information in this manual is Juniper Networks, NetScreen, and ScreenOS are registered trademarks of Juniper.
|Published (Last):||7 October 2016|
|PDF File Size:||7.88 Mb|
|ePub File Size:||2.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Connect to the Juniper SSG firewall console port with a console cable so you can see the output as you reset the device. The same concept applies to the other models that support NSRP; the difference being the interface notation or dedicated HA port. The console will confirm the config erase sequence is complete and the firewall device will begin a full reset. Generate your traffic now.
What are the minimum NSRP commands required? The default IPv4 address is The default login is netscreen: When it arrived the config had not been erased as stated, but I’ve done this before on a Netscreen and the process is exactly guidd same for both Juniper Netscreen and SSG firewalls.
Leave this field empty.
Whilst the information provided is correct to the best of my knowledge, I am not reponsible for any issues that may arise using this information, and you do so at your own risk. Yes – Enter the command: Firewall’s with identical ScreenOS versions and license keys Firewall’s with identical hardware At least one interface on each firewall to be configured in the HA zone, which will be used for carrying control channel information For more information on the software and hardware requirements for NSRP, refer to KB Your email address will not be published.
Now the device has erased the configuration and rebooted, a login prompt will be displayed.
Designed and Hosted by Andy Barnes. This process is quite simple once you get the timing right.
How to configure Juniper SSG
Defining a single name for all cluster members allows SNMP communication and digital certificates use to be continued without interruption after failover. Other NSRP firewall pairs on the same segment must have a different set of cluster ids. To do a factory reset you can either use the reset pinhole on the device or login to the serial console with the serial number as username and password. This command must be used on the current master! Notify me of follow-up comments by email.
This brings the current master unit into backup mode. Then proceed to the next step when ready to configure NSRP. System resetare you sure? You do not need to do this but without seeing the reset confirmation prompts, it cnfiguration take you many failed attempts in the dark! Perform basic configuration on Firewall-A. For more information on assigning the HA ports, refer to KB Configuration modifiedsave? The session commands list sessions that are currently active.
You need to use a paperclip or similar. These are only the commands that are needed for deep troubleshooting sessions that cannot be done solely on the GUI. I had some trouble with the application layer guude functionality on the ScreenOS devices. The traffic log shows already finished sessions of guise only if they were logged:. Each NSRP cluster member can have different host names. We’ll assume you’re ok with this, but you can opt-out if you wish.
Once the cluster id is set to a value, all the security interfaces will become part of the VSD-group 0, by default. Here are some hidden commands that help while troubleshooting the ALGs:. Both ways are explained here.
Only one digital certificate is required for an NSRP cluster. For assistance with configuring a pair of firewalls for NSRP, follow the steps below.
Configure NTP command, if applicable. Leave a Reply Cancel reply Your email address configuratino not be published. Configure the NSRP cluster id: If you have forgot your password I’m not aware of any other method other than to reset the device and reconfigure it. And to do a manual failover. Then continue to Step 7.
The switch ports which are configured with this IPv4 address vary! As always before performing anything; check, double check, test and always ensure you have a backup. Thanks and continue the good job.
These instructions were performed on a SSG The basic configuration steps for the following topology are documented in this solution.